[Omnetpp-l] Re: help :(

[Rudolf Hornig <rudolf.hornig at xxx>]

Hello, 

sorry for the late reply. We were busy bringing the new community site online. We already have an empty page in wiki how to do scatter charts, but have not found the time to do this. I think your problem would be a good example. If you don't mind sending me your INI file and all the sca files, I would use it as an example for the wiki article (and you would also get the solution :)

http://www.omnetpp.org/pmwiki/index.php?n=Main.Omnetpp4

Hope this is ok, Rudolf

On Mon, May 25, 2009 at 9:46 AM, dan get <twt_bob at xxx> wrote:

Hi Rudolf,
I was taking a look at the example, mine is a little bit different, the measurement is done for varying number of hosts/nodes, and I want to plot the mean delay vs number of hosts. Do you have an idea how to do that?

dan

---

From: Rudolf Hornig <rudolf.hornig at xxx>

To: omnetpp-l at xxx

Sent: Saturday, May 23, 2009 9:08:00 AM

Subject: Re: [Omnetpp-l] help :(

What you are looking for is called "scatter plots". There is an example for this in the samples/resultfiles/PureAlohaExperiment.anf where the channel utilization is drawn as a function of packet interarrival time (if memory serves)

Rudolf

On Fri, May 22, 2009 at 4:13 PM, dan get <twt_bob at xxx> wrote:

I increased the transmit power and works fine. I have another question though :P

I want to plot the mean delay vs the number of hosts using the IDE analysis tool. But when I choose plot it makes bar graph. My question is if I can specify the X-axis parameter(i.e. number of hosts in this case).

dan 

---

From: Alfonso Ariza <aarizaq_m at xxx>

To: omnetpp-l at xxx

Sent: Wednesday, May 20, 2009 7:31:20 PM

Subject: Re: [Omnetpp-l] help :(

 

The distance between nodes is too high, and the protocol can’t find other nodes and it can’t build a mesh network

Alternatives

Introduce more nodes

And/Or Reduce the playground size

And/Or increase the transmission distance

From: dan get

Sent: Wednesday, May 20, 2009 10:24 AM

To: Omnetpp-l at xxx

Subject: Re: [Omnetpp-l] help :(

---

From: dan get <twt_bob at xxx>
To: Omnetpp-l at xxx
Sent: Wednesday, May 20, 2009 10:14:24 AM
Subject: help :(

I want to simulate an ad hoc network using aodv routing. I want to measure delay and throughput. But when I see my result file(.sca), the values for mean delay, min delay, max delay, total sent, total received equal to zero, which is sad. Can you tell me why in the world this happens? I put my ini file if that helps.

best regards,

dan

Oops I forgot to put the ini file

[General]
#debug-on-errors = true
sim-time-limit = 3000s
seed-0-mt = 5
num-rngs = 2
network = manet_Grid_movilidad

cmdenv-express-mode = true
tkenv-plugin-path = ../../../Etc/plugins
#tkenv-default-run=1

description = "Aodv Simple test"

**.vector-recording = false
**.scalar-recording = true
cmdenv-express-mode = true

*.numHosts = 20
*.nodeSeparation = 150
*.playgroundSizeX = 2000
*.playgroundSizeY = 1000

**.channelNumber = 0
**.numberOfChannels = 1
**.debug = true
**.coreDebug = false
**.channelNumber = 0

**.wlan.mgmt.frameCapacity = 10

# channel physical parameters
*.channelcontrol.carrierFrequency = 2.4GHz
*.channelcontrol.pMax = 2.0mW
*.channelcontrol.sat = -110dBm
*.channelcontrol.alpha = 2
*.channelcontrol.numChannels = 1

# udp apps (on)
**.host[*].udpAppType="UDPBasicBurst"
**.host[*].numUdpApps=1

**.host[0].udpApp[0].destAddresses ="random_name(host)"
**.host[1].udpApp[0].destAddresses="random_name(host)"
**.host[2].udpApp[0].destAddresses="random_name(host)"
**.host[3].udpApp[0].destAddresses="random_name(host)"
**.host[4].udpApp[0].destAddresses="random_name(host)"
**.host[5].udpApp[0].destAddresses="random_name(host)"
**.host[6].udpApp[0].destAddresses="random_name(host)"
**.host[7].udpApp[0].destAddresses="random_name(host)"
**.host[8].udpApp[0].destAddresses="random_name(host)"
**.host[9].udpApp[0].destAddresses="random_name(host)"
**.host[10].udpApp[0].destAddresses="random_name(host)"
**.host[11].udpApp[0].destAddresses="random_name(host)"
**.host[*].udpApp[0].destAddresses=""

**.udpApp[0].localPort=1234
**.udpApp[0].destPort=1234
**.udpApp[0].messageLength=512B # Bytes
**.udpApp[0].messageFreq = 0.25s
**.udpApp[0].message_freq_jitter=uniform(-0.001s,0.001s,1)
**.udpApp[0].burstDuration  = 0s #uniform(1,4,1)
**.udpApp[0].activeBurst=true # if false all packet to the same address, if true select new destination per burts
**.udpApp[0].time_off = 0s # uniform(10,20,1))
**.udpApp[0].time_begin = uniform(1s,60s,1)
**.udpApp[0].limitDelay =20s
**.udpApp[0].rand_generator=1
**.udpApp[0].time_end=0s


**.host*.mobilityType = "inet.mobility.NullMobility"
**.host*.mobility.updateInterval = 0.1s
**.host*.mobility.scrollX = 50
**.host*.mobility.scrollY = 50
**.host*.mobility.nodeId = -1


# tcp apps (off)
**.numTcpApps=0
**.tcpAppType="TelnetApp"

# ip settings
**.routingFile=""
**.ip.procDelay=10us
# **.IPForward=false

# ARP configuration
**.networkLayer.proxyARP = true  # Host's is hardwired "false"
**.arp.retryTimeout = 1s
**.arp.retryCount = 3
**.arp.cacheTimeout = 100s

# manet routing
**.manetrouting.manetmanager.routingProtocol = "DYMOFAU"



# nic settings
**.wlan.mgmt.frameCapacity = 10
**.wlan.mac.address = "auto"
**.wlan.mac.maxQueueSize = 14
**.wlan.mac.rtsThresholdBytes = 3000B
**.wlan.mac.bitrate = 54Mbps
**.wlan.mac.basicBitrate = 24Mbps  # 24Mbps
**.wlan.mac.retryLimit = 7
**.wlan.mac.cwMinData = 31
**.wlan.mac.cwMinBroadcast = 31
**.wlan.mac.opMode = 2 # 802.11g
**.wlan.mac.slotTime = 9us #
**.wlan.mac.AIFSN = 2 #DIFS



# channel physical parameters
*.channelcontrol.carrierFrequency = 2.4GHz
*.channelcontrol.pMax = 2.0mW
*.channelcontrol.sat = -110dBm
*.channelcontrol.alpha = 2
*.channelcontrol.numChannels = 1

**.wlan.radio.transmitterPower = 2.0mW
**.wlan.radio.pathLossAlpha = 2
**.wlan.radio.snirThreshold = 4dB  # in dB
**.wlan.radio.bitrate = 54Mbps        
**.wlan.radio.thermalNoise = -110dBm
**.wlan.radio.sensitivity = -85dBm      
**.wlan.radio.phyOpMode = 2 #1/2  802.11b/802.11g-only
**.wlan.radio.channelModel = 1 #1/2  rayleigh/awgn
**.wlan.radio.berTableFile = "per_table_80211g_Trivellato.dat"



**.broadCastDelay=uniform(0s,0.005s)

#/ parameters : DYMOUM
**.no_path_acc_ = false
**.reissue_rreq_ = false
**.s_bit_ = false
**.hello_ival_ = 0
**.MaxPktSec = 20 #// 10
**.promiscuous = false
**.NetDiameter = 10
**.RouteTimeOut = 3000
**.RouteDeleteTimeOut = 3000*5 #//5*RouteTimeOut
**.RREQWaitTime = 1000
**.RREQTries = 3
**.noRouteBehaviour = 1

 #   //  parameters: AODVUU;
**.log_to_file = false
**.hello_jittering = true
**.optimized_hellos = true
**.expanding_ring_search = true
**.local_repair = true
**.rreq_gratuitous = true
#**.debug = false
**.rt_log_interval = 0
**.unidir_hack = 0
**.internet_gw_mode = 0
**.receive_n_hellos = 1
**.ratelimit = 1000
**.llfeedback = false# //1000
**.wait_on_reboot = 0
**.active_timeout = 6000 # // time in ms
**.internet_gw_address = "0.0.0.0"

#  //  parameters: DSRUU;
**.PrintDebug = true
**.FlushLinkCache = true
**.PromiscOperation = false
**.UseNetworkLayerAck = false
**.BroadCastJitter = 20 # 20  ms
**.RouteCacheTimeout = 300 #300 seconds
**.SendBufferTimeout = 300# //30 s
**.SendBufferSize = -1
**.RequestTableSize = -1
**.RequestTableIds = -1
**.MaxRequestRexmt = -1 #// 16,
**.MaxRequestPeriod = 10 #//10 SECONDS
**.RequestPeriod = 500 #//500  MILLISECONDS
**.NonpropRequestTimeout = 30# //30  MILLISECONDS
**.RexmtBufferSize = -1 #//MAINT_BUF_MAX_LEN
**.MaintHoldoffTime = 250# //250 MILLISECONDS
**.MaxMaintRexmt = 2 # //2
**.TryPassiveAcks = true #//1
**.PassiveAckTimeout = 100# //100 MILLISECONDS
**.GratReplyHoldOff = 1 #, //1 SECONDS
**.MAX_SALVAGE_COUNT = 15 # //15
**.LifoSize = 20
**.PathCache = true
**.ETX_Active = false
**.ETXHelloInterval = 1 #, // Second
**.ETXWindowNumHello = 10
**.ETXRetryBeforeFail = -1
**.RREPDestinationOnly = false
**.RREQMaxVisit = 5 # // Max Number that a RREQ can be processes by a node

#// Olsr
**.Willingness = 3
**.Hello_ival = 2
**.Tc_ival = 5
**.Mid_ival = 5
**.use_mac = 0 #1
**.Mpr_algorithm = 1
**.routing_algorithm = 1
**.Link_quality = 2
**.Fish_eye = false
**.Tc_redundancy = 3
**.Link_delay = true #//default false
**.C_alpha = 0.2

#// DSDV
**.manetroutingprotocol.hellomsgperiod_DSDV = 1 # //Period of DSDV hello message generation [seconds]
**.manetroutingprotocol.manetroutingprotocol.timetolive_routing_entry = 5 # // ;[seconds]
**.netmask = "255.255.0.0" # //
**.MaxVariance_DSDV = 1
**.RNGseed_DSDV = 0


seed-0-mt = 1209575029
seed-1-mt = 449294716
**.host*.mobility.traceFile = "esce_10_no_pausa.1"

---

_______________________________________________
Omnetpp-l mailing list
Omnetpp-l at xxx
http://lists.omnetpp.org/mailman/listinfo/omnetpp-l

_______________________________________________
Omnetpp-l mailing list
Omnetpp-l at xxx
http://lists.omnetpp.org/mailman/listinfo/omnetpp-l

_______________________________________________
Omnetpp-l mailing list
Omnetpp-l at xxx
http://lists.omnetpp.org/mailman/listinfo/omnetpp-l

--~--~---------~--~----~------------~-------~--~----~
You received this message because you are subscribed to the Google Groups "omnetpp" group. 
 To post to this group, send email to omnetpp at xxx 
 To unsubscribe from this group, send email to omnetpp+unsubscribe at xxx 
 For more options, visit this group at http://groups.google.com/group/omnetpp?hl=en
-~----------~----~----~----~------~----~------~--~---